Get a Hatch Trim Quote

Direct wholesale pricing, fast response.
Inspected Hatch Hardware

The smart Way to Buy Hatch Mouldings Online

Is your rear hatch trim cracked, faded, or falling off? We provide fully audited OEM liftgate mouldings that restore your vehicle's rear aesthetics and protect your hatch electronics. Fast shipping across New Jersey and nationwide.

Stud Integrity Verified

We ensure every mounting bolt and plastic tab is present for a rattle-free fit.

Camera Ready

Each piece is checked for precise port alignment for factory backup cameras.

Tested used OEM hatch liftgate moulding trim with clean finish

Genuine Used Rear Hatch Garnish for All Makes

The hatch moulding is a high-traffic component that often doubles as the grab handle for opening your rear door. Over time, the mounting studs can snap or the chrome can pit. At Falcon Car Parts, we specialize in providing genuine used hatch mouldings salvaged from vehicles with low environmental wear. Why settle for a loose aftermarket trim piece that vibrates every time you shut your hatch?

Every used replacement hatch trim we ship is cleaned and inspected for hairline cracks. Our technicians verify that the light lens windows are clear and that any integrated trunk release buttons are functional, providing a "factory-new" feel at a used part price.

  • Aesthetic Audit: Verified free of deep scuffs or chrome delamination.
  • Bolt Integrity: We ensure all rear mounting studs have clean, usable threads.
  • VIN Specific: Matched to your vehicle's specific emblem and handle design.

Fast NJ Delivery for Used Hatch Trim

Based in Clifton, NJ, Falcon Car Parts is your local source for used hatch mouldings in New Jersey. We understand that a broken hatch handle or garnish makes your SUV difficult to use. We offer rapid local shipping to Newark, Jersey City, and the surrounding Tri-State area. Get your part and fix your hatch today!

NJ Local Shipping

Fastest delivery to NJ, NY, and CT!

Hatch Trim for Every SUV & Hatch

From chrome license plate surrounds to lower hatch impact protectors.

Upper Garnishes

OEM trim pieces that sit above the license plate, often housing the handle and backup camera.

Lower Hatch Shields

Durable plastic or metal mouldings that protect the bottom edge of the hatch from bumper impacts.

Integrated Lighting Trim

Specialized hatch mouldings with factory wiring for LED license plate lamps and emblems.

Our 6-Point Quality Check for Hatch Mouldings

Rear-end precision requires structural excellence. Every used moulding passes this inspection:

  • 1. Stud Pull-Test: We verify that the metal mounting studs are firmly anchored in the plastic housing.
  • 2. Handle Stress Audit: For trim with integrated handles, we check for hairline fatigue cracks from use.
  • 3. Chrome Plating Review: We ensure there is no peeling or "pitting" caused by winter road salt.
  • 4. Lens Clarity Check: Integrated light lenses are checked for yellowing or moisture-trapping cracks.
  • 5. Seal Pliability: We check any rubber weather-seals to ensure they will prevent water from entering the hatch.
  • 6. Part Number Validation: We verify the engineering code against your VIN for a 100% plug-and-play match.

Common Questions About Used Hatch Mouldings

Used OEM hatch mouldings typically cost between $50 and $155. Luxury chrome garnishes or those with built-in electronics (like cameras or proximity sensors) are at the higher end.

This is usually due to the plastic mounting clips or studs snapping off inside the hatch. Because people pull on these mouldings to close the door, they undergo high stress. Our used mouldings are guaranteed to have all studs intact.

Generally, the camera is sold separately. The moulding is the plastic/chrome surround. However, if you need the camera as well, let us know when requesting your quote so we can provide a complete assembly.

Yes. You typically need to remove the interior hatch plastic panel to access the nuts holding the studs. Once the nuts are removed, the moulding pops right off. It’s a 30-45 minute job.

Absolutely. OEM mouldings use high-grade plastics that won't warp or rattle. Aftermarket hatch trim often has poor alignment, causing the hatch release handle to stick or the camera view to be tilted.

We match your factory paint code via your VIN. While there may be slight differences due to sun exposure on your vehicle, an OEM used part is the best way to get a near-perfect match compared to unpainted aftermarket parts.

Many used hatch mouldings include the light harness and lenses. We verify the lenses aren't cracked or hazy so your rear lighting remains bright and legal.

Pitting is caused by road salt eating through the chrome finish. We only sell "Grade-A" chrome mouldings that have been checked for a smooth, mirror-like finish.

Yes! Visit our facility for same-day local pickup. We keep a deep inventory of SUV and hatchback trim ready for immediate availability.

Hatch mouldings are often long and thin. We ship them in heavy-duty cardboard tubes or reinforced flat boxes with bubble wrap to ensure they arrive perfectly straight.