Get a Hood Hinge Quote

Direct wholesale pricing, fast response.
Inspected Body Hardware

The smart Way to Buy Used Hood Hinges Online

Is your hood misaligned or difficult to close? We provide precision-inspected OEM hood hinges that ensure a smooth pivot and perfect body gaps. Fast shipping across New Jersey and nationwide.

Alignment Verified

Each hinge is checked on a flat surface to ensure zero structural bending.

Smooth Pivot

We verify all pivot points are fluid and free of seized bushings.

Quality inspected used hood hinge with clean pivot points

Genuine Used Hood Brackets for All Makes

Hood hinges are often overlooked until a hood won't stay up or starts rubbing against the fender. A bent hinge can lead to permanent damage to your hood's sheet metal. At Falcon Car Parts, we specialize in providing genuine used hood hinges that offer factory-grade steel strength. Why risk the poor geometry and weak rivets of cheap aftermarket hinges?

Every used replacement hood hinge we inventory is salvaged from non-collision donor vehicles. Our technicians verify the spring tension and ensure the mounting bolt holes are not elongated, providing a "bolt-on" solution for perfect panel gaps.

  • Structural Audit: Verified zero stress-fractures or impact damage.
  • Rust Inspection: Checked for surface integrity to prevent pivot seizing.
  • VIN Matching: 100% guarantee that the hinge geometry matches your sub-model.

Fast NJ Delivery for Used Hood Hinges

Based in Clifton, NJ, Falcon Car Parts is your local source for used hood hardware in New Jersey. A hood that won't close properly is a major safety hazard—we offer expedited processing and rapid local shipping to get your vehicle secured today.

Serving Newark, Jersey City, Paterson, and the entire Tri-State area with reliable, tested OEM replacement parts.

NJ Local Shipping

Fastest delivery to NJ, NY, and CT!

Hinges for Every Vehicle Class

From standard pivot brackets to heavy-duty torsion spring assemblies.

Spring-Assisted Hinges

OEM hinges featuring heavy-duty coil springs designed to offset the weight of steel hoods.

Strut-Mount Hinges

Modern hinges with dedicated ball-stud mounts for gas-charged hood lift supports.

Active Pedestrian Hinges

Safety-equipped hinges found on newer models that pop up during an impact to protect pedestrians.

Our 6-Point Quality Check for Hood Hinges

Body alignment starts with a perfect pivot. Every used hinge passes the following strict inspection:

  • 1. Planar Straightness Test: We ensure the hinge arms aren't twisted, which causes hood "kick-up."
  • 2. Pivot Play Audit: We check for excessive "slop" or side-to-side movement in the rivets.
  • 3. Bolt Hole Integrity: Mounting areas are checked for elongation or damage from loose hardware.
  • 4. Lubrication Sweep: Every hinge is cleaned and its pivot fluidity is verified.
  • 5. Finish Condition: We check for excessive corrosion that could weaken the steel structure.
  • 6. Part Number Validation: We match the OEM stamp to your VIN for a 100% direct-fit guarantee.

Common Questions About Used Hood Hinges

Used hood hinges typically range from $35 to $95 per side. Pricing varies based on the vehicle's year and if the hinge includes integrated assist springs or special safety sensors.

If your hood sits higher than the fender near the windshield, or if the hood rubs the fender when opening, your hinge is likely bent. Even a 1/8-inch bend can cause major alignment issues.

It is highly recommended. Replacing only one hinge often makes it difficult to get a perfectly even gap on both sides, as the older hinge may have slightly different tension or wear.

We do not guarantee a color match for used hinges, as they are often painted the same color as the donor vehicle's engine bay. However, because they are mostly hidden when the hood is closed, many customers install them as-is or give them a quick spray of primer.

Yes. OEM hinges use higher-strength steel and precision rivets. Aftermarket hinges are often made of thinner metal, which can flex under the weight of the hood, leading to poor alignment.

No. The lift supports (gas struts) are sold separately. The hinge will include the mounting ball or bracket required to attach your existing strut.

Road salt and lack of lubrication are the primary causes. If a hinge is stiff, forcing it open will almost always bend the hinge or the hood mounting point. Our used hinges are verified to move freely.

Generally, yes, as they bolt to the chassis. However, some heavy-duty engine variants (like Diesels) have heavier hoods that require hinges with stronger assist springs. We use your VIN to ensure the correct spring rate.

We sell the hinges as the brackets themselves. We recommend reusing your factory hardware, as these are high-grade bolts designed for structural body parts.

NJ customers typically receive body hardware within 1 business day. Local pickup at our Clifton warehouse is also an option for immediate repairs.