Get a Manifold Quote

Direct wholesale pricing, fast response.
Heat-Tested Engine Parts

The Reliable Way to Buy Used Exhaust Manifolds Online

Tired of that annoying exhaust tick? We provide high-durability, OEM-quality exhaust manifolds that are fully inspected for cracks and warping. Fast shipping across New Jersey and nationwide.

Thermal Inspected

Each manifold is checked for heat-stress fractures and surface flatness.

100% OEM Fit

Genuine factory castings ensure all O2 sensors and studs line up perfectly.

Inspected used cast iron exhaust manifold with clean mounting surface

Genuine Used Engine Headers for All Makes

A cracked exhaust manifold is more than just a noise issue—it can decrease fuel economy and allow dangerous fumes into the cabin. At Falcon Car Parts, we specialize in providing genuine used exhaust manifolds that offer the durability of factory engineering without the dealer price tag.

Every used exhaust header we ship is salvaged from low-mileage vehicles. Our technicians verify the integrity of the internal passages and ensure the oxygen sensor threads are clean and ready for installation.

  • Surface Flattened: Mating surfaces checked to prevent gasket blowouts.
  • Crack Detection: Inspected under high light for stress fractures.
  • Thread Integrity: O2 sensor and mounting ports are chased and verified.

Fast Delivery for Exhaust Manifolds in NJ

Based in Clifton, NJ, Falcon Car Parts is your local expert for used exhaust manifolds in New Jersey. We understand that a cracked manifold can cause a failed inspection, which is why we offer expedited processing for all engine components.

Serving Newark, Jersey City, Paterson, and the entire Tri-State area with reliable, tested OEM replacement parts.

Next-Day NJ Delivery

Get your vehicle quiet and efficient again with fast local shipping!

Manifolds for Every Engine Config

From inline commuters to heavy-duty V8 trucks, we stock manifolds for all dricetrains.

Cast Iron Manifolds

Heavy-duty, traditional castings known for extreme heat resistance and long-term durability.

Tubular Steel Headers

Lighter weight OEM headers found on performance-oriented and modern aluminum block engines.

Integrated Maniverters

Combined manifold and catalytic converter units for modern emissions-compliant vehicles.

Our 6-Point Quality Check for Exhaust Manifolds

Engine performance depends on a leak-free exhaust. Every used manifold passes the following inspection:

  • 1. Straightedge Flatness Test: We verify the cylinder head mounting surface is perfectly flat to ensure a seal.
  • 2. Visual Crack Audit: A thorough inspection for "spider cracks" or separation in the casting.
  • 3. Port Carbon Check: We ensure ports are free of excessive carbon buildup or oil sludge.
  • 4. O2 Sensor Port Test: We test thread integrity so your oxygen sensor installs without seizing.
  • 5. Heat Cycle Review: We reject any units that show signs of severe warping from overheating.
  • 6. VIN Part Number Match: We match the casting ID to your vehicle options for 100% compatibility.

Common Questions About Buying Used Exhaust Manifolds

Used exhaust manifolds typically cost between $75 and $250. Prices vary based on the vehicle's make, model, and whether the manifold has an integrated catalytic converter (Maniverter).

Yes. Every manifold undergoes a heat-stress inspection and a dye-penetrant test if necessary to ensure there are no hairline cracks that could cause exhaust leaks or noise.

Used OEM manifolds are often superior because they are made from high-grade factory cast iron. Cheap aftermarket manifolds frequently warp or crack because they use thinner metal that cannot handle the same thermal loads.

We include the heat shield if it was in good condition on the donor vehicle. However, mounting hardware (studs and nuts) should always be purchased new for a safe installation.

A ticking sound that disappears as the engine warms up usually points to a gasket. A constant loud ticking or visible black soot marks around the manifold body usually indicates a structural crack.

Exhaust manifolds are engine-specific. We use your VIN to match the exact casting number to ensure all bolt holes and sensor ports line up perfectly with your existing cylinder head.

Absolutely. We check the mating surface with a machinist’s straightedge. If a manifold is warped beyond factory tolerances, it is rejected to ensure you get a leak-free seal against the head.

A Maniverter is an exhaust manifold with an integrated catalytic converter. We stock these units, but verify your state's emissions laws before purchasing a used emissions component.

Cracks are usually caused by extreme thermal expansion and contraction. Driving through deep puddles with a hot engine or failing engine mounts that put mechanical stress on the manifold are common causes.

For NJ customers, we offer 1-day shipping or same-day local pickup at our Clifton facility. We process exhaust parts with high priority because leaks can allow dangerous fumes into the cabin.