Get a Drive Shaft Quote

Direct wholesale pricing, fast response.
Certified Drivetrain Parts

The Best Way to Buy Used Rear Drive Shafts Online

Experiencing highway-speed vibrations or clunking? We offer fully inspected, balanced OEM rear drive shafts that restore smooth power to your wheels. Fast shipping across New Jersey and nationwide.

Straightness Tested

All shafts are checked for runout and tube integrity.

U-Joint Certified

Bearings and cross-joints inspected for zero play.

Close up of a tested used rear drive shaft assembly

Quality Used Rear Propeller Shafts You Can Trust

The rear drive shaft (or propeller shaft) is the backbone of your drivetrain, delivering power from the transmission to the rear differential. A bent shaft or a seized U-joint can cause catastrophic damage to your gearbox. At Falcon Car Parts, we specialize in providing genuine used rear drive shafts that are factory-balanced and ready for heavy-duty use.

Every used rear shaft in our inventory is carefully removed from donor vehicles and undergoes a multi-point inspection process. We check for tube dents, yoke alignment, and the health of the carrier bearing (on multi-piece shafts).

  • Vibration-Free: Inspected to ensure all factory balance weights are intact.
  • OEM Reliability: Superior metallurgy compared to cheap, thin aftermarket tubing.
  • Spline Inspection: Slip yokes are checked for wear and internal scoring.

Fast Delivery for Used Drive Shafts in NJ

Located in Clifton, NJ, Falcon Car Parts is perfectly positioned to provide rapid shipping for used rear drive shafts in New Jersey. Drivetrain issues shouldn't keep your vehicle grounded. We prioritize getting your components delivered to your doorstep or mechanic fast.

From Jersey City to Newark and beyond, we are the Tri-State area's trusted source for reliable, tested OEM drivetrain parts.

Rapid Tri-State Shipping

Daily shipments to NJ, NY, and CT!

Rear Shafts for Every Vehicle Configuration

Whether you have a short-bed regular cab or a long-wheelbase cargo van, we stock the exact length you need.

Steel Drive Shafts

Standard heavy-duty shafts found on most RWD and 4WD trucks and SUVs.

Aluminum Assemblies

Lightweight shafts used in performance sedans and modern pickups for better fuel economy.

Multi-Piece Shafts

Complex shafts featuring center carrier bearings for extended-length vehicles.

Our 6-Point Quality Check for Rear Drive Shafts

Drivetrain safety is our priority. Every used rear shaft sold by Falcon Car Parts passes the following standards:

  • 1. Straightness Dial Test: We verify the shaft has zero runout to prevent high-speed wobbling.
  • 2. U-Joint Articulation: Cross-joints are moved through their full range to ensure zero binding or 'grit.'
  • 3. Weld Integrity Check: We inspect the factory welds at both yokes for any signs of stress or cracks.
  • 4. Slip Yoke Review: We ensure internal splines are sharp and the outer seal surface is polished and clean.
  • 5. Carrier Bearing Audit: For 2-piece shafts, we check the center bearing for noise and the rubber for dry rot.
  • 6. VIN Compatibility: We confirm the wheelbase and transmission type to ensure a 100% bolt-on fit.

Common Questions About Buying Used Rear Drive Shafts

Used rear drive shafts typically cost between $100 and $300. Prices vary based on the shaft material (steel vs. aluminum) and whether it is a single-piece or two-piece design.

Common signs include a loud 'clunk' when shifting into gear, intense vibrations felt through the seat at highway speeds, or a squeaking noise from failing U-joints.

Yes, provided it is checked for runout. We inspect every shaft for tube integrity and verify that the U-joints move smoothly before shipping.

Aluminum shafts are lighter and help reduce drivetrain vibration and fuel consumption, whereas steel is heavier and more resistant to physical impact.

Yes, our shafts come complete with factory U-joints and yokes. We only sell units where the joints are tight and move freely.

No. Our shafts are factory-balanced. As long as the tube is not dented and the weights are intact, it is ready for immediate installation.

OEM shafts use high-grade alloys and are balanced to strict factory tolerances. Aftermarket shafts often use thinner tubing that can cause vibrations.

For long-wheelbase vehicles, we sell the complete multi-piece assembly. We inspect the center bearing for rubber rot and quiet operation.

Yes. We inspect the splines for any twisting and ensure the slip surface is smooth to prevent leaks at the transmission seal.

Based in Clifton, NJ, we offer 1-2 day delivery for local customers and incredibly fast shipping nationwide for all propeller shafts.